Skylight and glass roof systems bring natural daylight into the inner parts of buildings and allow atriums, circulation areas and wide roof openings to be enclosed with transparent overhead structures. In overhead glazing, however, architectural appearance is only one part of the design. Water management, glass safety, thermal and solar control, structural performance and maintenance access directly affect the long-term performance of the system.
A successful skylight is therefore not created simply by selecting a suitable glass type or aluminum profile. The following parameters must be resolved as one coordinated system:
-
roof geometry,
-
slope,
-
rainwater drainage,
-
condensation control,
-
glass configuration,
-
snow and wind loads,
-
supporting structure,
-
glass supports,
-
gaskets and sealants,
-
thermal movement,
-
operable vents,
-
maintenance and glass-replacement access.
For an overview of the system types and applications, see Optimal Mimarlık – Roof Skylight and Winter Garden.
Skylight Design Should Begin with Geometry, Not Glass Selection
The first design decision should not be the glass brand or glass thickness.
The following should first be defined:
-
width and length of the opening,
-
roof form,
-
ridge and valley locations,
-
glass module direction,
-
design slope,
-
rainwater flow direction,
-
supporting-structure grid,
-
interfaces with the existing building.
For large openings, glass modulation and structural framing cannot be designed independently.
A good example is the Açı College Skylight Application, where an opening of approximately 8 × 8 m, or about 64 m², was enclosed with a project-specific glass roof. The glass modules, structural requirements and perimeter connections were evaluated together rather than as separate design decisions.
For an opening of this scale, simply increasing glass thickness is not a complete design solution. Glass module size, supporting spans and allowable structural deflection must be coordinated.
Why Is Slope Critical in a Skylight Glass Roof?
Slope is one of the main parameters affecting glass-roof performance.
Insufficient slope can lead to:
-
water remaining on the glass,
-
accumulation of dirt and sediment,
-
prolonged water exposure at joints and gasket lines,
-
staining of the glass surface,
-
increased maintenance requirements.
There is no single minimum slope that is correct for every skylight system.
The required slope depends on:
-
profile geometry,
-
glass module length,
-
glass-joint configuration,
-
drainage capacity,
-
roof geometry,
-
system manufacturer requirements.
For this reason, a technical specification should not simply state that “a glass roof shall be installed.” The design slope and drainage principle should also be defined.
How Should Rainwater Drainage Work in a Glass Roof?
Skylight water management should not depend only on the external gutter.
The drainage path should be defined at the design stage:
glass surface → glass joints → profile drainage channels → valley or main collection channel → rainwater outlet
A limited amount of water reaching a controlled drainage zone through an external gasket or glazing joint does not automatically mean that the system has failed.
The key requirement is that this water:
-
does not enter the interior,
-
does not remain trapped inside the profile,
-
is discharged through the designed drainage route.
Internal drainage paths should be:
-
continuous,
-
adequately sized,
-
correctly levelled,
-
open at their discharge points.
Why Should Primary and Secondary Drainage Be Considered Separately?
Two different water-management layers may exist in a skylight.
Primary Drainage
Primary drainage carries rainwater from the external glass surface toward valleys, gutters and rainwater outlets.
Secondary Drainage
Secondary drainage removes limited amounts of water that pass the first weather line and enter controlled profile or glazing channels.
Secondary drainage paths should not be blocked by:
-
silicone,
-
sealant,
-
polyurethane foam,
-
screws,
-
installation debris.
A technically correct system may lose its drainage capability if its internal channels are blocked during installation.
Where Are Concealed Drainage Systems Used?
In architectural skylights where exposed gutters are undesirable, water can be collected through concealed channels integrated into the glazing and supporting system.
In the Alarko Kabataş–Mahmutbey Metro Octagonal Skylight, the octagonal glass roof incorporated concealed water drainage channels as part of the overall system.
The skylight geometry, glass joints, steel structure, EPDM membrane, drainage and perimeter insulation were coordinated through common details.
This project demonstrates that skylight drainage should not be treated as an accessory added after the structural design. It should be integrated into the profile and supporting-system geometry from the beginning.
Why Are Valleys and Gutter Zones More Critical?
At valleys and intersections between roof slopes, the amount of water flowing through the system increases.
These locations are more exposed to:
-
high short-duration rainwater flow,
-
snow accumulation,
-
leaves and dirt,
-
ice formation,
-
blocked outlets.
Valley and gutter dimensions should therefore be evaluated not only for average rainfall but also for intense rainfall and realistic maintenance conditions.
Drainage outlets should also remain accessible for inspection and cleaning.
Why Does Condensation Form in Glass Roofs?
Condensation forms when the internal surface temperature of the glass or profile falls below the dew-point temperature of the indoor air.
The risk increases with:
-
high indoor humidity,
-
low external temperature,
-
significant thermal bridging,
-
insufficiently insulated profiles,
-
inappropriate glass configuration,
-
poor internal air circulation.
Because a skylight is an inclined overhead surface, condensation behaves differently from water on a vertical facade.
Water can travel along the inner surface of the glass and reach:
-
lower glass edges,
-
aluminum profiles,
-
glass supports,
-
interior finishes.
The design should therefore aim both to reduce condensation risk and to control any limited condensation that still occurs.
Is Condensation Drainage the Same as Rainwater Drainage?
No.
Rainwater is managed on the external drainage plane.
Condensation may occur around:
-
internal glass surfaces,
-
internal profile cavities,
-
glass-edge zones,
-
pressure plates,
-
thermal-bridge locations.
Some skylight systems therefore incorporate dedicated condensation collection channels and internal drainage routes.
The concealed drainage arrangement used in the Alarko Metro skylight is an example of an integrated approach in which external water and condensation-related moisture are considered as part of the same coordinated roof-glazing system.
What Type of Glass Should Be Used in a Skylight?
Overhead glazing is exposed to different loads and safety conditions than vertical facade glass.
A glass roof may be subjected to:
-
self-weight,
-
snow load,
-
positive and negative wind pressure,
-
maintenance loads,
-
accidental impact,
-
fall hazards after glass breakage.
Depending on the project, the glazing configuration may include:
-
thermally toughened glass,
-
laminated glass,
-
toughened laminated glass,
-
insulating glass units,
-
Low-E coated glass,
-
solar-control glass.
The final configuration should be determined according to glass dimensions, support conditions, structural loads and safety requirements.
Why Is Laminated Glass Important in Skylights?
Post-breakage behaviour is a critical safety issue in overhead glazing.
In laminated glass, two or more glass plies are bonded with an interlayer. If the glass breaks, the interlayer helps retain fragments within the glazing assembly.
EN – European Standard
EN 14449 – Glass in Building – Laminated Glass and Laminated Safety Glass
is one of the principal European product standards for laminated glass.
EN 14449 – Laminated Glass and Laminated Safety Glass
EN 14449 covers laminated glass and laminated safety glass products used in buildings.
For projects in Türkiye, the applicable TS EN – Turkish adoption of the relevant European Standard and its current status should be checked through the Turkish Standards Institution.
TSE – Turkish Standards Institution
Where Does Thermally Toughened Glass Fit into the Design?
Thermal toughening increases the mechanical and thermal resistance of glass.
EN 12150-1 – Glass in Building – Thermally Toughened Soda Lime Silicate Safety Glass
defines the principal characteristics of thermally toughened safety glass.
However, specifying only “toughened glass” is not sufficient for an overhead glazing system.
The entire glazing make-up, including post-breakage behaviour, should be evaluated.
How Is Impact Safety Evaluated?
EN 12600 – Glass in Building – Pendulum Test – Impact Test Method and Classification for Flat Glass
is used to classify the impact behaviour and breakage characteristics of flat glass.
The standard does not determine glass thickness on its own. It is one component of the overall safety evaluation.
Why Should Glass Thickness Not Be Selected from a Catalogue Table Alone?
Glass thickness should not be selected solely by looking at panel width and height.
The calculation should consider:
-
glass dimensions,
-
two-edge or four-edge support,
-
roof inclination,
-
snow load,
-
wind load,
-
glass build-up,
-
properties of laminated interlayers.
EN 16612 – Glass in Building – Determination of the Lateral Load Resistance of Glass Panes by Calculation
is one of the principal references used for calculating glass panes under lateral loading.
How Should an Insulating Glass Unit Be Selected?
For skylights enclosing heated or cooled interiors, an:
IGU – Insulating Glass Unit
is commonly used.
EN 1279 – Glass in Building – Insulating Glass Units
is a multi-part standard covering matters including:
-
system description,
-
dimensional tolerances,
-
moisture penetration,
-
gas leakage,
-
edge-seal performance,
-
factory production control.
EN 1279 – Insulating Glass Units
The series includes six principal parts addressing general requirements, moisture penetration, gas leakage, edge seals, conformity assessment and production control.
Why Are Low-E and Solar-Control Glass Important in Skylights?
A skylight faces the sky and can receive significant solar radiation.
With large glazed roof areas, inappropriate glass selection may cause:
-
excessive summer heat gain,
-
higher cooling demand,
-
reduced indoor thermal comfort,
-
glare.
Glass selection should therefore consider more than Ug value alone.
Relevant parameters include:
-
visible light transmission,
-
solar factor,
-
total solar-energy transmittance,
-
Low-E coating,
-
solar-control coating.
EN 410 – Glass in Building – Determination of Luminous and Solar Characteristics of Glazing
is one of the principal references for determining the luminous and solar properties of glazing.
For coated glass, the:
EN 1096 – Glass in Building – Coated Glass
series is also relevant.
EN 1096-4 – Coated Glass Product Standard
EN 1096-4 covers the product standard and assessment of coated glass used in buildings.
What Does Ug Mean?
Ug – Glass Thermal Transmittance
describes the thermal transmittance of the centre area of a glazing unit.
A lower Ug value indicates better thermal insulation performance of the glass unit.
EN 673 – Glass in Building – Determination of Thermal Transmittance (U Value)
is one of the principal calculation standards used for this value.
The overall thermal performance of a skylight, however, is not determined by Ug alone.
Thermal bridges through:
-
aluminum profiles,
-
glass-edge zones,
-
spacers,
-
supporting connections
must also be considered.
Why Is Snow Load Critical in Skylight Design?
A glass roof is directly exposed to snow loading.
Snow load depends on:
-
project location,
-
altitude,
-
roof inclination,
-
roof geometry,
-
parapets,
-
adjacent higher surfaces,
-
local snow drifting.
Valley zones and intersections between different roof levels may be particularly sensitive to local snow accumulation.
EN 1991-1-3:2025 – Eurocode 1: Actions on Structures – Part 1-3: Snow Loads
provides principles and rules for determining snow loads for the structural design of buildings and civil engineering works.
For projects in Türkiye, the applicable TS EN version, National Annex provisions and current project requirements should be checked.
How Does Wind Affect a Glass Roof?
Skylight surfaces can be subjected to both positive wind pressure and suction.
Wind effects depend on:
-
building height,
-
roof form,
-
skylight geometry,
-
distance from roof edges,
-
corner and edge zones,
-
surrounding development.
EN 1991-1-4:2026 – Eurocode 1: Actions on Structures – Part 1-4: Wind Actions
is the current second-generation European wind-action standard. It was published in 2026 and provides rules for wind actions on buildings and civil engineering works.
Project designers should verify the applicable national adoption and transition rules before using a specific generation of Eurocode.
The Supporting Structure Cannot Be Designed Independently of the Glass
The load path in a skylight generally follows:
glass → glass supports and glazing profiles → aluminum framing → steel or aluminum primary structure → building structure
The supporting system should be selected by considering:
-
span,
-
glass module size,
-
glass weight,
-
snow load,
-
wind load,
-
profile spans,
-
deflection,
-
thermal movement.
The Optimal Mimarlık References page includes İnnovia Skylight / Esenyurt, where the system is identified as a steel structure and skylight application.
In wide-span glass roofs, the steel structure is not only responsible for carrying the glass weight. It also controls module geometry and limits deformation so that glazing joints and drainage paths remain within the intended design tolerances.
How Was the Supporting System Resolved in the Alarko Metro Skylight?
In the Alarko Kabataş–Mahmutbey Metro application, the octagonal skylight incorporated an NPI 140 steel supporting structure, specialized profiles for the glass joints, concealed drainage channels, EPDM membrane and composite panel interfaces.
The steel structure and glazing system were coordinated along common geometric axes.
This demonstrates why large skylights should be treated as a single structural and envelope system rather than as separate steel and glazing packages.
Why Can Excessive Deflection Cause Water Leakage?
Excessive structural deformation is not only a structural issue.
Too much deflection may cause:
-
glass joints to move beyond their intended range,
-
reduced gasket compression,
-
excessive strain in sealants,
-
changes in the designed roof slope,
-
reverse falls in drainage channels.
Supporting structures should therefore be checked for both strength and serviceability.
Why Are Glass Supports and Setting Blocks Important?
Glass panels should not rest directly and uncontrolled on metal profiles.
Glass supports and setting blocks:
-
transfer glass weight to the supporting system,
-
prevent direct glass-to-metal contact,
-
control panel position,
-
allow the required movement of the glazing.
Incorrect support positions may create concentrated edge stresses, especially in large and heavy insulating glass units.
How Should Thermal Movement Be Resolved?
Glass, aluminum and steel do not expand by the same amount under the same temperature change.
In large skylights, thermal movement may be significant in:
-
long aluminum profiles,
-
sun-exposed roof surfaces,
-
dark-colored metal finishes.
The design may therefore require:
-
fixed and sliding connections,
-
profile movement joints,
-
controlled glazing joints.
Thermal movement should not be completely restrained unless the system has been specifically engineered for that condition.
How Should Glass Joints Be Designed?
The joint between glass modules should consider:
-
glass manufacturing tolerances,
-
installation tolerances,
-
profile movement,
-
glass movement,
-
allowable sealant movement.
A joint that is too narrow may restrict movement.
An unnecessarily wide joint may create excessive sealant width, water retention and visual problems.
The 18 mm glass joints used in the Alarko Metro octagonal skylight were a project-specific solution developed for that geometry and profile arrangement; they should not be interpreted as a universal skylight joint dimension.
Silicone Alone Is Not a Waterproofing System
One of the common mistakes in glass roofs is relying entirely on an external silicone line for water protection.
A well-designed skylight works through:
slope + weather seal + profile geometry + secondary drainage + primary discharge
Silicone is one component of the system.
Increasing the quantity of silicone does not compensate for incorrect drainage design.
How Does Glass-Roof Design Change in a Winter Garden?
In a winter garden, the glass roof is not an isolated overhead component. It operates together with vertical glazing, doors and ventilation systems to form the complete enclosure of an occupied space.
The design should therefore coordinate:
-
glass roof-to-wall junctions,
-
solar control,
-
thermal insulation,
-
rainwater drainage,
-
condensation control,
-
operable doors,
-
ventilation.
The Optimal Mimarlık References page lists Tulip A Villa / Hadımköy as a Winter Garden & Folding Aluminium Doors application.
This type of application illustrates how a glass roof and large operable vertical surfaces must be detailed as a single enclosure rather than as independent products.
A further example is the Alkent 2000 Winter Garden Application, where a glass roof was combined with thermally insulated lift-and-slide aluminum doors and solar-control tempered laminated insulating glass. The project considered daylight, solar control, thermal insulation, water tightness and controlled drainage together.
What Should Be Considered for Operable Skylight Vents?
Where operable vents are used for ventilation, the following should be evaluated together:
-
vent dimensions,
-
glass weight,
-
actuator capacity,
-
opening angle,
-
wind action,
-
gasket compression,
-
drainage in the closed position.
Operable sections are among the most sensitive parts of a skylight in terms of water tightness.
A Smoke-Vent Skylight Is a Separate System
The fact that a skylight vent can open does not automatically make it a smoke-exhaust system.
Smoke-control design should consider:
-
fire scenario,
-
required aerodynamic or effective opening area,
-
automation,
-
fire alarm integration,
-
power supply,
-
emergency operating strategy.
Applicable fire regulations and project-specific fire engineering requirements should be checked separately.
Why Should Maintenance Access Be Resolved During Design?
A skylight is a maintainable building element.
Areas requiring periodic inspection include:
-
gutters,
-
valley outlets,
-
drainage openings,
-
glass joints,
-
sealants,
-
gaskets,
-
motorized vents,
-
glass surfaces.
The design should therefore consider:
-
safe maintenance routes,
-
service access,
-
fall protection,
-
glass replacement procedures.
A skylight that cannot be safely accessed for cleaning and repair may develop significant long-term operational problems even if its original construction is technically sound.
What Should a Skylight Technical Specification Include?
A specification stating only:
“A glass skylight roof shall be installed.”
is not sufficient.
At minimum, the following should be defined:
-
system geometry,
-
design slope,
-
glass modulation,
-
glazing configuration,
-
glass safety requirements,
-
target Ug value,
-
solar-control requirements,
-
snow load,
-
wind load,
-
supporting system,
-
deflection criteria,
-
glass supports,
-
profile system,
-
gasket and sealant system,
-
primary drainage,
-
secondary drainage,
-
condensation drainage,
-
thermal movement,
-
operable vents,
-
maintenance access,
-
glass replacement method.
What Should Be Shown in Skylight Shop Drawings?
A skylight shop drawing – fabrication and installation drawing package should show:
-
plan,
-
sections,
-
glass modules,
-
glass identification numbers,
-
profile grid,
-
primary steel or aluminum supporting members,
-
glass supports,
-
ridge details,
-
valley details,
-
perimeter terminations,
-
glass joints,
-
drainage channels,
-
discharge points,
-
condensation channels,
-
operable vents,
-
building interfaces,
-
maintenance access.
Fabrication should not be based only on the architectural roof plan.
Technical Standards for Skylight and Glass Roof Design
| Subject | Standard / Technical Reference |
|---|---|
| Snow loads | EN 1991-1-3:2025 – Eurocode 1, Snow Loads |
| Wind actions | EN 1991-1-4:2026 – Eurocode 1, Wind Actions |
| Lateral resistance of glass panes | EN 16612 – Glass in Building, Lateral Load Resistance |
| Thermally toughened safety glass | EN 12150-1 – Thermally Toughened Safety Glass |
| Laminated safety glass | EN 14449 – Laminated Glass and Laminated Safety Glass |
| Impact classification | EN 12600 – Pendulum Impact Test |
| Insulating glass units | EN 1279 series – Insulating Glass Units |
| Glass thermal transmittance | EN 673 – Determination of Thermal Transmittance |
| Luminous and solar properties | EN 410 – Luminous and Solar Characteristics |
| Coated glass | EN 1096 series – Coated Glass |
For projects in Türkiye, the corresponding TS EN – Turkish adoption of European Standards, relevant National Annexes and the edition in force at the date of design should be verified through the Turkish Standards Institution.
Recommended Skylight Design Sequence
A coordinated skylight design process generally follows this order:
-
Define the roof opening and geometry.
-
Establish slope and water-flow directions.
-
Determine valleys, gutters and drainage points.
-
Develop the glass modulation.
-
Determine snow and wind actions.
-
Calculate the glazing configuration.
-
Define thermal and solar-control targets.
-
Design the primary supporting structure.
-
Check structural deflection.
-
Select the aluminum glazing system.
-
Resolve glass supports and setting blocks.
-
Design primary and secondary drainage.
-
Assess condensation risk.
-
Define glass joints.
-
Resolve thermal movement.
-
Define operable vents and automation where required.
-
Design maintenance and glass-replacement access.
-
Complete shop drawings.
-
Fabricate and install according to the approved design.
Quick Answers
Does a skylight glass roof require slope?
Yes. Slope supports rainwater drainage, reduces standing water and helps keep the surface cleaner. The required slope depends on the system and project details.
Why does a skylight leak?
Possible causes include insufficient slope, blocked drainage channels, incorrect glass joints, poor sealant application, inadequate secondary drainage or excessive structural deformation.
Can silicone alone waterproof a skylight?
No. Silicone is only one part of the weather-sealing system. Slope, profile geometry, gaskets and drainage must work together.
Why is laminated glass used in skylights?
Laminated construction helps retain broken glass fragments within the assembly and improves post-breakage safety in overhead glazing.
How is skylight glass thickness determined?
Glass dimensions, support conditions, snow load, wind load and glazing make-up should be evaluated together by calculation.
Why does condensation form in skylights?
Condensation may form when the internal surface temperature of the glass or profile falls below the dew point of the indoor air.
Are rainwater drainage and condensation drainage the same?
No. Rainwater is handled on the external drainage plane, while condensation is managed around internal profile and glass-edge zones.
Do skylights require snow-load calculations?
Yes. The glass, glazing profiles and primary supporting structure should be checked for the applicable snow load.
Do skylights require wind calculations?
Yes. Glass and supporting systems should be evaluated for both positive wind pressure and suction.
Is a winter garden the same as a skylight?
No. A skylight is primarily an overhead glazed enclosure. A winter garden combines the glass roof with vertical glazing, doors, ventilation and occupied-space comfort requirements.
Why is maintenance access important?
Gutters, drainage paths, glass joints, sealants, gaskets and operable vents require periodic inspection and maintenance. Safe access should be resolved during design.
Technical Editor and Content Review:
Mehmet Beşe Polatkan, Architect (YTU)
Copyright and Use
This content belongs to Optimal Mimarlık Yapı ve Tic. A.Ş. and is protected under Law No. 5846 on Intellectual and Artistic Works of the Republic of Türkiye.
It may not be copied, reproduced, or republished without permission. For quotations made within the scope of Article 35 of Law No. 5846, the source must be cited as Optimal Mimarlık – www.optimalmimarlik.com.
© Optimal Mimarlık Yapı ve Tic. A.Ş.

















